This fixes recognition of $error and $fatal statements in the output of
XSim when running run_testbenches.py. XSim apparently prints a "shift
in" character (0x15) as part of its error statements, so the regular
expression was not matching.
Original-commit: ee36d7fabcf73f773edae00fbb1604a600db992d
This adds time alignment to the radio, so that the first transmitted or
received sample gets shifted into the position corresponding to its
timestamp. The applies only to configurations in which SPC > 1.
For example, if the radio time is incrementing by 4 samples per cycle
(SPC = 4) starting at time 0, and a packet is supposed to be
transmitted at time 201, then the data must be left-shifted by one
sample (201 % 4 = 1), so that the first sample of the packet correctly
aligns with the radio sample corresponding to time 201. Things get more
complicated if the radio time is not a multiple of the SPC (i.e., the
radio time started at time 1, 2, or 3 instead of 0).
Original-commit: 9afa6be7b270047cb03cbd5a16482e5d19edc3dd
This module supports timed sample alignment by shifting radio words
with multiple samples per cycle to put the first sample into the
correct position for the required timestamp.
Original-commit: 0a13db4afaaf88dda3bd194bbf20271c690d5c7f
Patch AR76780 was already listed as a requirement for X4xx and N3xx,
but was not listed as a requirement for X3xx and E3xx. This change
makes it required for all Vivado-based USRPs.
Original-commit: 5aa6bc4418a30d6e6fde80b80632f9f9115ea5c4
- Fix NODE_INST
- Fix RFNOC_PROTOVER
- Add option to use SystemVerilog transport adapter for raw UDP
Original-commit: 0114e108af63d9ac785649c8099a042299624943
- Fix NODE_INST
- Fix RFNOC_PROTOVER
- Add option to use SystemVerilog transport adapter for raw UDP
Original-commit: 693ec2c896306bcba3686385e5861593040d4cbd
This adds several features to the SystemVerilog Eth/IPv4/UDP transport
adaptor including:
- Compat register
- NODE_INST register
- Capabilities register
- KV map access for custom routing on RX data paths
- CHDR header removal for raw payloads to be sent over UDP
Also adds xport_adapter_ctrl.py, which allows controlling the new
registers.
Co-authored-by: Martin Braun <martin.braun@ettus.com>
Original-commit: 3c3da4c62f33d02bb05bcdc38e8929cbf2cdd9a3
Set the NODE_INST parameter for each transport adapter on X4xx so that
each adapter has a unique node instance number.
Original-commit: 8e87a4d24aeeb77a9528ff67a36d8a0ae12e7137
The NODE_INST parameter was set to 0. This adds it as a parameter so
that each transport adapter can have a unique node instance number.
Original-commit: c6bfd2e7f8313d727c2e557958f1b1ac2f674d98
The NET_CHDR_W parameter tells the transport adapter what CHDR width
is used in transport packets, such as Ethernet packets. By default the
CHDR width used by the transport and RFNoC core will be the same. The
NET_CHDR_W parameter can be used in situations where the RFNoC core
expects a CHDR width from the transport adapter that is different from
that used over the network. In this situation, the transport adapter
will rewrite the CHDR packets so that each side gets the expected CHDR
width.
Original-commit: a9e49b7c587ef778ee0fe327e8bdcb15e0b0fc95
In Vivado 2021.1, it is no longer allowed to use "default: 0" to
initialize an enum within a packed struct. So we must initalize enum
data members explicitly now.
Original-commit: 8007b6b4dff5b64d476b2e3ccb68a777c2f02c8b
This fixes some issues with the 2021.1 version of the 10 GbE IP. In the
new version, link status is sporadically detected by the Xilinx IP when
nothing is connected to the port. Also, when the SFP is inserted, the
link status goes up and down multiple times. This change fixes this by
adding a counter and only considering it "linked" when the link has
been stable for some amount of time.
Original-commit: 846c7be2e42f1db6d7c7cc0b1128e014f83e3bae
This adds the ability to do IP generation and FPGA builds using the
--jobs (-j) option with Make. For example, rather than generating each
IP one after another, you can generate up to N at a time using N Vivado
instances. This greatly reduces the IP generation time. Similarly,
parallel jobs can be used to easily build different FPGA variants
simultaneously.
Because FPGA builds can consume a lot of memory, care must be taken to
ensure that the number of jobs is not too high for the amount of memory
available.
New IP make targets were added for each USRP so that IP can be built
separately from the FPGA. The IP targets are now a dependency on each
FPGA target.
For example, you can generate the IP for X310 using 4 parallel jobs
using the following command:
make -j4 X310_IP
Or, build two X310 bitstreams simultaneously:
make -j2 X310_XG X310_HG
Original-commit: 4b03e237a96ee277eefff257d65b08708c38662c
This fixes warnings regarding the first argument to $fatal(), which is
supposed to be a number indicating what diagnostics to display. 1
corresponds to "Prints simulation time and location".
Original-commit: 58763bdfdaa276155ec6b79a3e5420de17172c7a
This causes the latest RFNoC protocol version to be used by default
and avoids the need to update YAML files every time the RFNoC
protocol version gets bumped.
Original-commit: 92016a585a5223a9a7678134e318e412875b64c2
Update USRP RFNoC iamge core YAML files to use the more consistent
device port names. Clean up the formatting and make the files more
consistent.
Original-commit: 6318eaeff548f760056af7c8172937a296409d25
This updates all RFNoC devices so that they get the RFNoC protocol
version and CHDR width in the same way, from the output generated by
the RFNoC image builder.
Original-commit: 6f038dc2f69b38e715206b2e700fdd3a1bbc638e
Change name in DRAM IP Makefile from IP_MIG_7SERIES_TG_SRCS to
IP_DDR3_16BIT_TG_SRCS to match the naming of other variables.
Original-commit: febf339e0df412e54cf43a204c280128d8ca1ec3
Before this change, the packet size output by the Replay block during
playback was limited to length of a full memory burst transaction.
This led to relatively small packets during playback (typically
2 KiB) and had other side effects, such as simultaneous playback from
two different memory locations using different packet sizes because of
differences in memory alignment.
With this change, the configured packet size, as set by the register
REG_PLAY_WORDS_PER_PKT, is used for all packets except the last
packet of playback, which can of course be smaller.
Original-commit: 082a733c326d6332d581d5b7bf9ee86a503ba502
This sets the Replay block's counter width so that memory bursts are
up to 2 KiB. Previously, the counter width was fixed, which meant
that wide memories would require especially large buffers and could
exceed the 4 KiB limit imposed by AXI.
Original-commit: 08d03f881e2767f45ab7fc18c8003c9739b0ffb2
Change the width of the crossbar in the AXI Interconnect IP from
256-bit to 512-bit to match the DRAM memory controller width and to
give better performance.
Original-commit: 822cd03c8cd686f8b0554774adcbdd3803128bc2
This adds two additional ports to the DRAM, for a total of up to
four channels connected to DRAM.
Original-commit: a91d8e49655dd6f69ce1153498266c1a95230772
Change AWIDTH to be the same as MEM_ADDR_W by default. Current USRPs
assume the AXI address width is the same as MEM_ADDR_W.
Original-commit: 6936a9ac664cbc312fd17a5ebab9b40069615f7a
This adds DRAM support to E31x devices. Due to the size of the DDR3
memory controller, it is not enabled by default. You can include the
memory controller IP in the build by adding the DRAM environment
variable to your build. For example:
DRAM=1 make E310_SG3
Original-commit: 788fef11ef890c6dcee3be495fc381bcf2990d3b
This change causes HLS IP to be exported with a version of 1.0.0
instead of a date code. Due to a bug in Vivado, date codes after
0x7FFFFFFF (anything in 2022 or beyond) cause an error. Setting
an explicit revision avoids this issue.
See Xilinx AR 76960 for details.
Original-commit: 51384afc2c5d4db9e2e45d97382edce8c8039b10
Previously, when running rfnoc_image_builder, the rfnoc_image_core.vh
file in the main x400 directory was being used instead of the one
generated by rfnoc_image_builder.
Original-commit: 121b6c560cacfb5deacdee664dd1f32cafef7b3d
Some comments describing data flow direction were wrong. This commit
updates the Mako files and updates the noc_shell modules with newly
generated versions.
Original-commit: 270a7e13c365d05ba04ab44a2f844d96ba15f43b
The I and Q were swapped in sine_tone, which caused confusion and made
the rotation of REG_CARTESIAN clockwise by default. This effectively
made the resulting frequency negative. This PR makes the I and Q order
consistent with RFNoC and fixes the direction of rotation so that a
positive value for REG_PHASE_INC (phase increment) results in a
counter-clockwise rotation, which yields a positive frequency.
Original-commit: 4e6531f30648ede5be8f93fa49fdcd4973b73813
Updates the language in setupenv.sh --help to better reflect that there
are many locations where Vivado is searched.
Original-commit: e64d3e28316f642c1203722b6f5f2af710a7e281
This adds a Verilog definition named `UHD_FPGA_DIR that corresponds to
the location of the UHD "fpga" directory. This allows you to include
files in your out-of-tree modules relative to the FPGA directory. For
example, you could include the library header file rfnoc_chdr_utils.vh
using the following:
`include `"`UHD_FPGA_DIR/usrp3/lib/rfnoc/core/rfnoc_chdr_utils.vh`"
Some simulators may not support `" outside of the context of a `define,
in which case you can do the following:
`define RFNOC_CHDR_UTILS_PATH \
`"`UHD_FPGA_DIR/usrp3/lib/rfnoc/core/rfnoc_chdr_utils.vh`"
`include `RFNOC_CHDR_UTILS_PATH
Original-commit: 66267f515802ff3f965fd44e1f0d3097ada7484f
This sets the ARCH and PART_ID environment variables so that the
selected part family is used for simulations by default. This can be
overridden by changing them in the Makefile for the testbench if a
testbench requires a specific part family. Prior to this change, the
default was always ARCH=kintex7, PART_ID=xc7k410t/ffg900/-2, which
required support for that part to be installed.
Original-commit: c176046dff4941bcec27b0b72e5a68264c4808e5
There were some rare corner cases where the EOB could get lost in the
DUC due to the dds_timed logic not always passing it through as it
should. This resulted in an underflow error message at the end of
transmission.
This commit also fixes an issue where part of the last packet
used a frequency shift of 0 instead of the requested frequency
shift, and an issue where the first few samples of a burst used the
wrong frequency shift value.
Part of the fix includes adding a TUSER port to dds_sin_cos_lut_only.
The TUSER port is built into the IP but was disabled. It is now
enabled and set to 1 bit wide. This has a very small effect on
resource usage and can be left unconnected when not needed.
The dds_freq_tune block was shared by the DUC and DDC. To avoid
affecting the DDC, a new version, dds_freq_tune_duc, is being
added for the DUC to use that has the necessary fixes.
The new dds_wrapper.v is a wrapper for the dds_sin_cos_lut_only IP.
This IP has the undesirable behavior that new inputs must be provided
to push previous outputs through the IP. This wrapper hides that
complexity by adding some logic to ensure all data gets pushed through
automatically. This logic uses the TUSER port on the IP.
Finally, a testbench for dds_timed was added.
Original-commit: 77975d108a704ce18ec52b4ee1764381b1893752
PkgComplex adds functions for doing complex arithmetic in SystemVerilog
simulation.
PkgMath provides mathematical operations and constants that aren't
built into SystemVerilog, such as a constant for pi and the function
round().
PkgRandom adds randomization functions beyond what standard Verilog
supports but that don't require any special licenses or simulators.
Original-commit: da4202e6f74796603072aa14544581604e81df02
Updated some comments that still referenced the old CORDIC
implementation, which is no longer used.
Original-commit: 18e5bdfa100a40376147d1a497645345b2a938b1
Wade Fife