Previously, if a write occurred before the FIFO was ready then a
write could hang as the data channel would complete but leave the
address channel in a state where it would never complete. The fix is
to hold off acknowledging on the data channel until the FIFO is ready.
Original-commit: 3f6ad749b06094b0e16b412a791ba3f2ac509600
Add DEFAULT_M and DEFAULT_N parameters for rate changing cores.
This allows the host to not need to configure fixed rate change
cores.
Original-commit: 983fad664436301c31c3bc8c81b538a41537598b
This change allows detection of attempting to execute setupenv.sh
rather than sourcing it, which is required.
Original-commit: 6faec1d4a14a1af52681aabf19c9040dcee772ff
This adds support for colored output and support for directories added
to the list of source files (for HLS support).
Original-commit: 5b3d66e5b7cedb7098de3e4dbbee70af04a3626e
For HLS builds, the output file names aren't known in advance. This
makes it difficult to write the Makefile to pull in the files and pass
them to the build tools. This change allows you to add a directory as
your HDL source so that all files in the directory will be pulled in by
the build process.
Original-commit: 90933d9b2faf392fd26f3f7ca32f73719614a40a
The address ranges configured for the AXI interconnect IP limited the
amount of accessible DRAM to two 32 MB regions. This change makes the
full 1G available to all DRAM ports.
Original-commit: bba0cddfadcb744e8a6fae27d57ba8d3995eaf64
The decimation in the rx_frontend_gen3 was added to reduce the bandwidth
between the Radio and the DDC due to the limitation in bandwidth over
the crossbar for dynamically connected blocks. The default FPGA image
for the X300 now has a static connection between the Radio and DDC, so
this is no longer necessary.
This change allows the TwinRX receive channels to be time aligned with
channels from other daughterboards so they can be used in the same
streamer.
Signed-off-by: Michael West <michael.west@ettus.com>
Original-commit: d0c162bc7a4ac82f6104506b17d7be05e1780336
Sets time increment based on tick rate and sample rate instead of
assuming one tick per sample. Defaults to legacy behavior.
Minor compat number bumped on DUC and DDC blocks.
Signed-off-by: Michael West <michael.west@ettus.com>
Original-commit: 12dfb97c8efce40494efb35bdd81d06b6f8b9b62
Make timekeeper tick on every cycle of the radio clock.
Signed-off-by: Michael West <michael.west@ettus.com>
Original-commit: 7886b71f13e9f6e5786c95286ef98f49ab716119
This updates the chdr_to_axis method so that it doesn't change the
input chdr_packet object. This is useful in case there are other
references to that object in use. Not modifying the object means that
you don't always have to copy the object before passing it to this
method.
Original-commit: 259506c4993834d9ef8ccb48635623552b075237
The axis_data_to_chdr block previously only sampled the sideband
information at the end of the packet. This adds a parameter that
controls if the sideband information should be sampled at the beginning
of the packet or the end of the packet. In the former case, large
internal packet buffers are not required.
Original-commit: a8c4f021277cf3b0a0897fa9da0252541512f3a6
Add -voptargs=+acc to the default options when running vsim. This
option enables debug command access to objects in the design, which is
generally needed for debugging in the GUI.
Original-commit: eed2d2348cab7dc786673f0649373809d04027d5
The axis_split module takes a single AXI-Stream input and duplicates it
onto multiple AXI-Stream outputs. This block correctly handles the
somewhat tricky flow-control logic so that the AXI-Stream handshake
protocol is honored at all top-level ports.
Original-commit: fa0f4b2833119d57d331f592028ff9f032895c89
This commits enables the FPGA build infrastructure to require a very
specific Vivado version, all the way to the patch level.
Vivado typically has the following version format:
Year.release.update_patch
This commit enables setupenv_base.sh to optionally look for the
environment variable VIVADO_VER_FULL, which should contain the
full Vivado version in the format specified above.
Vivado is directly used to retrieve the installed version, returning
an error if the requested version is not found.
Example in setupenv.sh (which calls setupenv_base.sh):
VIVADO_VER=2019.1
VIVADO_VER_FULL=2019.1.1_AR73068
The setupenv.sh script will setup Vivado 2019.1, but it will also
verify that both Update 1 and patch AR73068 are installed.
Original-commit: 932b7cbb040cef7fce0c83f81839722fd8ad5bdf
Xilinx changed the way [all_registers -edge_triggered] is treated such
that set_max_delay constraints that use it can cause segmentation and
cause clocks to not be propagated to all endpoints. Changing to
[all_ffs] avoids this potential issue.
Original-commit: 55e422535292c29de00b80f15b0a49ca3fb94f26
viv_utils.tcl will now read files with the .sdc suffix using the
read_xdc Vivado command. This is especially useful when I/O timing
constraints in the FPGA and CPLD need to depend on a common constant.
Original-commit: b47b1a467ee5796dbce359ff34c9d55a6acebc82
The latency through the combiner is static if only one master interface
is used and PRIORITY=1 is set.
Original-commit: 4e3650c0d7ac9bea3720151fbb23591f187590c7
Xilinx changed the default Vivado install location from /opt/Xilix to
/tools/Xilinx. This commit adds support for finding Vivado in either
the new location or the old location.
Original-commit: 156d714b8fb288100d242ea200ae1d1dcd6bcd57
This adds the "modelsim" simulator option to run_testbenches.py to allow
for regression testing of the native ModelSim simulation target.
Original-commit: 39d6007ca7e3b27e8230db6690faa7469ca62cb2
This adds a simulation make target that allows you to run ModelSim
natively rather than through Vivado.
Adds or modifies the following simulation make targets:
make vlint - Brake up compilation to Verilog/SystemVerilog/VHDL
make modelsim - Depends on make vlint and invokes modelsim
Adds the following variables:
MODELSIM_ARGS - Added to invocation of ModelSim
SVLOG_ARGS - Added to SystemVerilog invocation of vlog
VLOG_ARGS - Added to Verilog invocation of vlog
VHDL_ARGS - Added to VHDL invocation of vcom
Original-commit: b296b26053d4437b8ae97e3df415a3d041b7b51e
When using viv_modify_tcl_bd, two Vivado instances are open:
1. GUI-mode Vivado that opens a TCL-based BD for the user to edit.
2. Batch-mode Vivado that saves changes from (1) and rewrites the TCL
source file.
During (2), the previous tool implementation was saving layout
information in the TCL source file. This layout info gets outdated
when the BD is reopened, because (1) regenerates the layout to provide
a clean BD diagram in the Vivado GUI.
Furthermore, each time the BD is open, the layout information will
vary due to Vivado's window size, thus creating untracked changes in
the source TCL file.
This commit removes the command option that requests Vivado to save
layout information.
Original-commit: feabc14cb5d5d26987d72b1a51638a83f8f39131
For example, the ChdrPacket typedef is being renamed from ChdrPacket to
ChdrPacket_t. This allows the code to distinguish between the
unparameterized class and the already parameterized class. This isn't
strictly necessary, but it makes some Vivado 2019.1 bugs easier to work
around. It also makes the code slightly less ambiguous.
Original-commit: df27e9fa05d2d767f69182763852f6803c5b2a34
This adds variants of the send and recv methods in RfnocBlockCtrlBfm
and ChdrIfaceBfm that input/output items instead of CHDR words.
Original-commit: aebcaea5eb4e28c5c2a1c78b5e8dd42e5d1247b6
This replaces chdr_word_t, which was a statically defined 64-bit data
type, with a paramaterizable data type that matches the defined CHDR_W.
Code that formerly referenced the chdr_word_t data type can now define
the data type for their desired CHDR_W and ITEM_W as follows:
// Define the CHDR word and item/sample data types
typedef ChdrData #(CHDR_W, ITEM_W)::chdr_word_t chdr_word_t;
typedef ChdrData #(CHDR_W, ITEM_W)::item_t item_t;
ITEM_W is optional when defining chdr_word_t if items are not
needed. Static methods in the ChdrData class also provide the ability to
convert between CHDR words and data items. For example:
// Convert CHDR data buffer to a buffer of samples
samples = ChdrData#(CHDR_W, ITEM_W)::chdr_to_item(data);
Original-commit: fc895feacb8dde3b02c9a4eccb4b4f4a654f2881
This changes the for loop to use the generate keyword, making it
compatible with Verilog 2001. This allows tools that only support
Verilog 2001 to use this file (e.g., Intel Quartus).
Original-commit: b92597e1c9b6f09d5e62e55a60e33c04d437a50a
This eliminates the complicated semaphore from the testbench and brings
the radio testbench in line with the other testbenches.
Original-commit: 8727642de2aa22e982e012d85d32325f664a3e9e
Adds a ZPU register to control the FP GPIO source. These are 2bits
per GPIO pin, totalling 24 bits. 0 corresponds to RF-A, 1 corresponds
to RF-B. The following Python code will control the upper 6 bits of the
front-panel GPIO from the B-side radio on an X300:
>>> import uhd
>>> U = uhd.usrp.MultiUSRP("type=x300")
>>> U.get_gpio_src_banks()
['FP0']
>>> U.get_gpio_src("FP0")
['RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFA',
'RFA', 'RFA']
>>> U.set_gpio_src("FP0", ['RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFA',
'RFB', 'RFB', 'RFB', 'RFB', 'RFB', 'RFB'])
>>> U.get_gpio_src("FP0")
['RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFB', 'RFB', 'RFB', 'RFB',
'RFB', 'RFB']
>>> # Make all GPIOs outputs:
>>> U.set_gpio_attr("FP0A", "DDR", 0xFFF)
>>> U.set_gpio_attr("FP0B", "DDR", 0xFFF)
>>> # Control all GPIOs from software (not ATR):
>>> U.set_gpio_attr("FP0A", "CTRL", 0x000)
>>> U.set_gpio_attr("FP0B", "CTRL", 0x000)
>>> # Bottom 3 pins go high from radio A
>>> U.set_gpio_attr("FP0A", "OUT", 0x007)
>>> # Top 3 pins go high from radio B
>>> U.set_gpio_attr("FP0B", "OUT", 0xE00)
Amends the gpio.cpp example to allow switching the source.
Co-authored-by: Brent Stapleton <brent.stapleton@ettus.com>
Original-commit: d7304cc724de43b0d61d5b9d61a528d58898f004
Andrew Moch