Together with an update to the LMK04832 register config according to
TIs data sheet, all clock outputs are now aligned to SYSREF rising edge.
Therefore, I needed to adjust the SYSREF capture mechanism inside the
RFSoC and the SYSREF LMK Delay.
SYSREF is now captured first at the falling edge of PRC.
To be on the safe side, we are still double synchronizing SYSREF
afterwards on the rising edges of PRC.
As we are now independent of any MCR regarding timing constraints the
SYSREF Delay is also set to '0' for all X4xx devices.
Original-commit: b5cb4fac42ab530174e108455b730ffa1510d70a
In cases when the info FIFO fills, it was possible for
in_pkt_info_tvalid to be asserted then on the next cycle
in_pkt_info_tready would deassert, in which case the input would be
dropped. This change ensures that tvalid remains asserted until tready
deasserts.
Original-commit: 6d2e9f983ae94d2e1e6866c34b3c87374a349631
The TX radio will normally transmit a late not-timed packet when an
underflow occurs between packets within a burst. However, if it was
only one cycle late, then the packet would be dropped. This change
rearms the state machine more quickly in this corner case to allow
this late packet to be accepted. The underflow error will still be
reported.
Original-commit: 9faac6597cf21ca11e40d4e98797cea2848c40b0
This Python utility was getting a bit rotten. The following updates
where made:
- Reformatted using ni-python-styleguide
- Fixed formatting of regex strings by declaring them 'raw'
- Updated docstrings and any linter issues
On Pyton 3.12 and beyond, this will no longer throw SyntaxError
warnings.
Original-commit: 0dede88c6535ae6ffb30b162c83dc01d59d3bfa0
Previously, the build tools for the FPGA bitfiles would try and
autodetect the Vivado executable, but would allow for a `vivado_lab`
executable. However, Vivado Lab Edition can't build bitfiles nor run
testbenches. Its only use with the USRP FPGA build tooling is to run
`viv_jtag_program` and `viv_jtag_list` (which are command-line proxies
for probing FPGAs attached to JTAG, and for programming bitfiles over
JTAG, e.g. to an X3x0).
When Vivado Lab and Vivado were present, it was possible that we ran
into issues where Vivado Labs would be preferred, and then builds or
testbenches would fail.
We therefore remove the ability to use Vivado Lab. Running the Vivado
Lab Edition with the GUI, and loading and probing bitfiles is of course
still possible, but tools like `rfnoc_image_builder` can no longer
accidentally try to use Vivado Lab instead of regular Vivado.
Original-commit: 21c4c591a51d520c7aac7108e853e59c4953f953
The tready signal that was used when EN_MAGNITUDE equals 0 was not
correct. This commit allows EN_MAGNITUDE to be disabled.
Original-commit: ef449523df61268d4efbc86a12cb098c2b2bf239
This replaces the legacy RFNoC FFT block with a new one of the same
name that includes a superset of the original features. New features
include cyclic prefix insertion or removal and FFT sizes up to 64k.
Original-commit: 25fffb006755b2e91f0138eb4af3ab9e16b8690c
The underlying Xilinx CORDIC IP uses 2 bits for the whole part of its
(X,Y) inputs and its magnitude output. So, having 17 bits means we have
enough precision to represent the entire range of an sc16. The 16-bit
CORDIC is insufficient to cover this entire range.
Original-commit: 0d3d69493aac9239ae437b04f291c61669678606
- Add documentation
- Add generate block labels
- Remove tabs and fix indentation
- Separate the code into three logical sections
Original-commit: 76074ecb319bf770805374b81c966b94cba898c5
This simplifies image core files by generating a RADIO_NIPC parameter
for the X410, X440 and E31x BSP files. The IO port widths for X410 are
now dynamically widened based on the NIPC value, which is a function of
the RF_BW parameter, and cannot be modified.
The radio block can now read the NIPC value from the BSP, and populate
its spc parameter dynamically. This avoids having to know the right spc
value when writing YAML image core files and reduces redundancy.
This also removes the RADIO_NIPC parameter entirely from all the image
core files. This parameter was fine, but it was a bit confusing because
it referenced a Verilog parameter, which you just had to know was there
in the generated Verilog. By referencing the BSP parameter instead, the
YAML files (BSP, radio.yml, and image core file) are now self-contained
regarding the RADIO_NIPC/spc information.
As a minor upside, the input wire widths for X410's and N310's
rfnoc_image_core.sv module are now generated with the correct widths,
and not, as before, with the worst-case width (and then we assume Vivado
will do the right thing).
Original-commit: 53b4d7a21018fe7aabf9f774260aefb41297a41b
... to support custom image core name, example:
rfnoc_image_builder -y n310_rfnoc_image_core.yml -n my_custom_name
The device tree source files were renamed to match the target
name used in the Makefile.
example:
old: dts/usrp_n310_fpga_hg.dts
new: dts/N310_HG.dts
The source file is used to compile the final .dts file in the BUILD_DIR.
example: build-my_custom_name/N310_HG.dts
The final .dts file is copied to the BUILD_OUTPUT_DIR as part of the
post build steps and renamed to the custom image core name.
example: build/my_custom_name.dts
This completes the change that was introduced with commit 2afc66f132.
Original-commit: d40db57f2e03c322ac6b0001e0a59d4a14a5a3b9
Not a functional change. The comments for the replay block in the
crossbar_routes reflect a single replay block, but the FPGA image
actually has two replay blocks with half the number of ports as the
single block design.
Original-commit: 32efa102ce592ff16204b67b9aeb244e9589166e
These bitfiles use four-port DRAM FIFOs and only connect two of those
ports. We skip the warnings as that is the intended build behaviour.
Original-commit: 52860eeb670da53c08dddb40dd950832b087acbe
The image builder will currently emit a warning if a NoC-block has
unconnected ports. This requires specifying `-W` to continue building,
which is the intended behaviour.
However, there are cases where there are legitimate reasons to not
connect a block, e.g., in the X310, where the radio block has 2x2 ports,
but we only connect 2 RX ports, and 1 TX port.
This adds a way to declare a "null" connection, which makes it explicit
in the image core YAML that a connection was deliberately omitted. Such
connections are created by connecting to a port called "_none_", e.g.:
```
connections:
- { srcblk: _device_, srcport: _none_, dstblk: radio0, dstport: in_1 }
```
The block name is irrelevant, but the schema requires providing a block
name.
This commit also amends the x3xx_radio_base.yml to avoid warnings when
building X3x0 bitfiles.
Original-commit: 6758966a5ac127a396e8b3b39f96aa484098e50f
This file was repeating entries from x410_radio_base.yml, which none of
the other x410 image core YAML files do.
Original-commit: 1ba6fdaf9c3a17cbb46f976f9d4dd8349cf5adb7
Initialize test_status for backwards compatability with testbenches
that don't call start_tb().
Original-commit: 72295360e65d989dd774deabc4add0a54eb6f97e
mschill