Fixing an issue in which a very slow radio_clk (due to low sample clock
rate) could cause bus transactions to be issued to the timekeeper
faster than it could service them, resulting in a timeout. This change
replaces RegPort with CtrlPort so that proper flow control can be
maintained to the timekeeper.
Original-commit: 2e910c5307702c3f3efb6dc8cb60f4f71ce11e67
It was set to E320_HG, which is not a valid target, causing build errors
unless -t E320_1G was provided to rfnoc_image_builder.
Original-commit: 9ed42affcaa88e026cb4f82807e69b546ed30c8c
Device was set to e31x, but this is not a valid device type. All e31x
devices use the e310 device type.
Original-commit: 60b76ebb31f9d1672c1b18367346b3fb522e13e9
This increases the size of the ingress buffers for the N320 radio to
support 250MHz TX streaming rates.
Signed-off-by: mattprost <matt.prost@ni.com>
Original-commit: e8db6fa4301ce471bf41ef14d5d38e5727199007
This adds new image files which come with a DRAM FIFO. The addition of
an N320 image with a DRAM FIFO allows DDR3 BIST to be run on an
assembled (motherboard + daughterboard) N320.
This image is intentionally very similar to the N300_AA and N310_AA
targets which serve the same purpose of providing an image with a DRAM
FIFO for their respective devices.
Original-commit: ae2b9bf7aeea6f8f98f6dacffdfc018d87107927
This updates the makefiles for the testbenches so they can be run using
"make modelsim" without any additional hacks. The "xsim" and "vsim"
simulation targets also still work.
Original-commit: e962cc4a5e51e2326eb656ee2a779ea26774687b
- Fixed some incorrect comments
- Fixed some missing wire declarations for internal NIC
- Fix wire declarations for GPIO (they were declared too late)
Original-commit: b18eaa75de2d1dcba2a1be0ee0b862a57e976cca
The address ranges configured for the AXI interconnect IP limited the
amount of accessible DRAM to two 32 MB regions. This change makes the
full 1G available to all DRAM ports.
Original-commit: bba0cddfadcb744e8a6fae27d57ba8d3995eaf64
Make timekeeper tick on every cycle of the radio clock.
Signed-off-by: Michael West <michael.west@ettus.com>
Original-commit: 7886b71f13e9f6e5786c95286ef98f49ab716119
Xilinx changed the way [all_registers -edge_triggered] is treated such
that set_max_delay constraints that use it can cause segmentation and
cause clocks to not be propagated to all endpoints. Changing to
[all_ffs] avoids this potential issue.
Original-commit: 55e422535292c29de00b80f15b0a49ca3fb94f26
Adds a ZPU register to control the FP GPIO source. These are 2bits
per GPIO pin, totalling 24 bits. 0 corresponds to RF-A, 1 corresponds
to RF-B. The following Python code will control the upper 6 bits of the
front-panel GPIO from the B-side radio on an X300:
>>> import uhd
>>> U = uhd.usrp.MultiUSRP("type=x300")
>>> U.get_gpio_src_banks()
['FP0']
>>> U.get_gpio_src("FP0")
['RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFA',
'RFA', 'RFA']
>>> U.set_gpio_src("FP0", ['RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFA',
'RFB', 'RFB', 'RFB', 'RFB', 'RFB', 'RFB'])
>>> U.get_gpio_src("FP0")
['RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFB', 'RFB', 'RFB', 'RFB',
'RFB', 'RFB']
>>> # Make all GPIOs outputs:
>>> U.set_gpio_attr("FP0A", "DDR", 0xFFF)
>>> U.set_gpio_attr("FP0B", "DDR", 0xFFF)
>>> # Control all GPIOs from software (not ATR):
>>> U.set_gpio_attr("FP0A", "CTRL", 0x000)
>>> U.set_gpio_attr("FP0B", "CTRL", 0x000)
>>> # Bottom 3 pins go high from radio A
>>> U.set_gpio_attr("FP0A", "OUT", 0x007)
>>> # Top 3 pins go high from radio B
>>> U.set_gpio_attr("FP0B", "OUT", 0xE00)
Amends the gpio.cpp example to allow switching the source.
Co-authored-by: Brent Stapleton <brent.stapleton@ettus.com>
Original-commit: d7304cc724de43b0d61d5b9d61a528d58898f004
The FPGA codebase was removed from the UHD repository in 2014 to reduce
the size of the repository. However, over the last half-decade, the
split between the repositories has proven more burdensome than it has
been helpful. By merging the FPGA code back, it will be possible to
create atomic commits that touch both FPGA and UHD codebases. Continuous
integration testing is also simplified by merging the repositories,
because it was previously difficult to automatically derive the correct
UHD branch when testing a feature branch on the FPGA repository.
This commit also updates the license files and paths therein.
We are therefore merging the repositories again. Future development for
FPGA code will happen in the same repository as the UHD host code and
MPM code.
== Original Codebase and Rebasing ==
The original FPGA repository will be hosted for the foreseeable future
at its original local location: https://github.com/EttusResearch/fpga/
It can be used for bisecting, reference, and a more detailed history.
The final commit from said repository to be merged here is
05003794e2da61cabf64dd278c45685a7abad7ec. This commit is tagged as
v4.0.0.0-pre-uhd-merge.
If you have changes in the FPGA repository that you want to rebase onto
the UHD repository, simply run the following commands:
- Create a directory to store patches (this should be an empty
directory):
mkdir ~/patches
- Now make sure that your FPGA codebase is based on the same state as
the code that was merged:
cd src/fpga # Or wherever your FPGA code is stored
git rebase v4.0.0.0-pre-uhd-merge
Note: The rebase command may look slightly different depending on what
exactly you're trying to rebase.
- Create a patch set for your changes versus v4.0.0.0-pre-uhd-merge:
git format-patch v4.0.0.0-pre-uhd-merge -o ~/patches
Note: Make sure that only patches are stored in your output directory.
It should otherwise be empty. Make sure that you picked the correct
range of commits, and only commits you wanted to rebase were exported
as patch files.
- Go to the UHD repository and apply the patches:
cd src/uhd # Or wherever your UHD repository is stored
git am --directory fpga ~/patches/*
rm -rf ~/patches # This is for cleanup
== Contributors ==
The following people have contributed mainly to these files (this list
is not complete):
Co-authored-by: Alex Williams <alex.williams@ni.com>
Co-authored-by: Andrej Rode <andrej.rode@ettus.com>
Co-authored-by: Ashish Chaudhari <ashish@ettus.com>
Co-authored-by: Ben Hilburn <ben.hilburn@ettus.com>
Co-authored-by: Ciro Nishiguchi <ciro.nishiguchi@ni.com>
Co-authored-by: Daniel Jepson <daniel.jepson@ni.com>
Co-authored-by: Derek Kozel <derek.kozel@ettus.com>
Co-authored-by: EJ Kreinar <ej@he360.com>
Co-authored-by: Humberto Jimenez <humberto.jimenez@ni.com>
Co-authored-by: Ian Buckley <ian.buckley@gmail.com>
Co-authored-by: Jörg Hofrichter <joerg.hofrichter@ni.com>
Co-authored-by: Jon Kiser <jon.kiser@ni.com>
Co-authored-by: Josh Blum <josh@joshknows.com>
Co-authored-by: Jonathon Pendlum <jonathan.pendlum@ettus.com>
Co-authored-by: Martin Braun <martin.braun@ettus.com>
Co-authored-by: Matt Ettus <matt@ettus.com>
Co-authored-by: Michael West <michael.west@ettus.com>
Co-authored-by: Moritz Fischer <moritz.fischer@ettus.com>
Co-authored-by: Nick Foster <nick@ettus.com>
Co-authored-by: Nicolas Cuervo <nicolas.cuervo@ettus.com>
Co-authored-by: Paul Butler <paul.butler@ni.com>
Co-authored-by: Paul David <paul.david@ettus.com>
Co-authored-by: Ryan Marlow <ryan.marlow@ettus.com>
Co-authored-by: Sugandha Gupta <sugandha.gupta@ettus.com>
Co-authored-by: Sylvain Munaut <tnt@246tNt.com>
Co-authored-by: Trung Tran <trung.tran@ettus.com>
Co-authored-by: Vidush Vishwanath <vidush.vishwanath@ettus.com>
Co-authored-by: Wade Fife <wade.fife@ettus.com>
Original-commit: bafa9d95453387814ef25e6b6256ba8db2df612f
- Fixed 10GigE firmware communication issues and sequence errors for TX
- Multiple changes to help ease timing closure
- Cleaned up build scripts
- Switched to Xilinx ISE 14.7 as the default build tool for X300
Original-commit: 64d71dcbc5fa6790385b288de25224d386b047b0
