Adds a 266.667 MHz compute engine clock and uses it instead of the
radio clock for the DDC and DUC. Using a faster clock than the radio
allows the DDC and DUC to drain after a stall in the data flow.
Original-commit: ab93cb0929b9536b6d6cbfdc4813e6ba169053ae
FPGA:
- Split up MB registers that control daughterboard specific settings so
that daughterboards 0 and 1 could have different setings, in
preparation for future devices that require different settings.
This requires a compat number bump to 8.0.
- Add registers for additional RFDC information, including the
block/tile mapping of the individual channels, and information about
resampling capabilities
- Identify sections of code that would be specific to X410/ZBX and move
them to their own headers, so it's trivial to add device-specific
sections of code instead for other devices in the future.
- This includes constraints for clocks and I/O pins.
- Remove ability to do timed ctrlport transactions to the MB CPLD, this
was unused and possibly broken.
- Move daughterboard-specific code into its own code location
(dboards/zbx)
- Move X410-specific register documentation to its own location
(doc/X410)
- Refactor Makefiles to split out X410/ZBX specific components and allow
switching between device types
- Add 512-bit AXI interconnects
- Make number of timekeepers configurable (X410 keeps the single
timekeeper)
MPM:
- Required compat is bumped to 8.0
- Now supports new registers for detecting DSP capabilities and
multi-rate settings for the daughterboards
- Adds MMCM controls (currently unused)
Co-authored-by: Wade Fife <wade.fife@ni.com>
Co-authored-by: Ryan Marlow <ryan@lmarlow.com>
Co-authored-by: Martin Braun <martin.braun@ettus.com>
Co-authored-by: Humberto Jimenez <humberto.jimenez@ni.com>
Original-commit: c1d268917ea65dd9c5a42366014cb96d3c025223
Removes the CPU_W parameter from x4xx.v and the qsfp_wrapper files. The
value of this parameter depends on the axi_eth_dma IP and therefore
should not be changed.
Original-commit: 84c49f40adc980e2968a6a844b4bdbb2d2d38c9c
Adds a BUILD_SEED make variable that can be set to a 32-bit integer,
and adds an FPGA read-only register initialized by this variable.
Changing this variable will randomly affect the FPGA build results.
This can be useful when your build fails timing by a small amount,
allowing you to build again and get different results with the same
code.
For example, you could run the following to produce an FPGA build with
different timing results from the default build:
make X310_XG BUILD_SEED=123
Original-commit: 3a3a03486f9221c2e59fa6d0826c23d17730956d
Set the NODE_INST parameter for each transport adapter on X4xx so that
each adapter has a unique node instance number.
Original-commit: 8e87a4d24aeeb77a9528ff67a36d8a0ae12e7137
Extends timed command support to all endpoints
addressable by the radio ctrlport interface.
Previously supported endpoints:
- Daughterboard GPIO interface
- RFDC timing control
Newly supported endpoints:
- DIO ATR control
- DIO SPI control
- DIO Source control
Original-commit: e51f18925a566f152c4e8622aac6376efe46c6eb
Include a register that contains SPI controller information.
Currently, it only provides the number of slaves addressable
by the SPI engine.
Original-commit: 1d7d1226e7576bfad484109afd3aad4e78af111b
Modify behavior of clock crossing between radio_clk and radio_clk_2x.
This ensures strobe signals are always asserted for a single
radio_clk_2x cycle and when radio_clk is low.
Original-commit: adb352a2ad81d7c6d70ec5880a787b6bab7d19ba
Javier Valenzuela