Patch AR76780 was already listed as a requirement for X4xx and N3xx,
but was not listed as a requirement for X3xx and E3xx. This change
makes it required for all Vivado-based USRPs.
Original-commit: 5aa6bc4418a30d6e6fde80b80632f9f9115ea5c4
This adds the ability to do IP generation and FPGA builds using the
--jobs (-j) option with Make. For example, rather than generating each
IP one after another, you can generate up to N at a time using N Vivado
instances. This greatly reduces the IP generation time. Similarly,
parallel jobs can be used to easily build different FPGA variants
simultaneously.
Because FPGA builds can consume a lot of memory, care must be taken to
ensure that the number of jobs is not too high for the amount of memory
available.
New IP make targets were added for each USRP so that IP can be built
separately from the FPGA. The IP targets are now a dependency on each
FPGA target.
For example, you can generate the IP for X310 using 4 parallel jobs
using the following command:
make -j4 X310_IP
Or, build two X310 bitstreams simultaneously:
make -j2 X310_XG X310_HG
Original-commit: 4b03e237a96ee277eefff257d65b08708c38662c
This causes the latest RFNoC protocol version to be used by default
and avoids the need to update YAML files every time the RFNoC
protocol version gets bumped.
Original-commit: 92016a585a5223a9a7678134e318e412875b64c2
Update USRP RFNoC iamge core YAML files to use the more consistent
device port names. Clean up the formatting and make the files more
consistent.
Original-commit: 6318eaeff548f760056af7c8172937a296409d25
This updates all RFNoC devices so that they get the RFNoC protocol
version and CHDR width in the same way, from the output generated by
the RFNoC image builder.
Original-commit: 6f038dc2f69b38e715206b2e700fdd3a1bbc638e
Before this change, only the channel 0 ATR state was sent to the
db_control module. For TwinRX, this had the disadvantage that when only
Channel 1 was used, the FP- and LED-GPIOs could not track the radio's
ATR state (e.g., no LED would light up in this case).
Note that unlike UHD 3, there is only one db_control module per slot.
There are therefore no options to map GPIOs to track the ATR state of an
individual channel.
Original-commit: f23ab72129041777bcd3357a1f4e37b29e62dd86
This sets the ARCH and PART_ID environment variables so that the
selected part family is used for simulations by default. This can be
overridden by changing them in the Makefile for the testbench if a
testbench requires a specific part family. Prior to this change, the
default was always ARCH=kintex7, PART_ID=xc7k410t/ffg900/-2, which
required support for that part to be installed.
Original-commit: c176046dff4941bcec27b0b72e5a68264c4808e5
Update rfnoc_image_core.v to take into account the new image_core_name
fields and version strings. Add new rfnoc_image_core.vh. Update YAML
where needed.
Original-commit: b0033158a4c520063540881451d8daac91e98714
Change version from a numeric to a string, in order to
differentiate between versions like "1.1" and "1.10".
Original-commit: ca21048bd2f832b20bb36763f76d46b861b697a5
Add the Replay RFNoC block to the RFNoC core image for x300, x310, n300,
n310, n320/n321, and e320. The Replay block is contained within its own
static connection, so previous default behavior is still supported.
Signed-off-by: mattprost <matt.prost@ni.com>
Original-commit: 437381bd2cfe137c5e7e2a70aab8226bfb1c70cd
This updates the IO signatures so that all devices and RFNoC blocks use
the same IO signature for the DRAM. This is needed because the IO
signatures must match between the RFNoC blocks and the devices. This
means that some devices have extra bits in the IO signature for the
address, but the extra bits will simply be ignored.
Original-commit: 8f09caaa06725d2364c63ac7cff02f3298895f4a
The address ranges configured for the AXI interconnect IP limited the
amount of accessible DRAM to two 32 MB regions. This change makes the
full 1G available to all DRAM ports.
Original-commit: bba0cddfadcb744e8a6fae27d57ba8d3995eaf64
Make timekeeper tick on every cycle of the radio clock.
Signed-off-by: Michael West <michael.west@ettus.com>
Original-commit: 7886b71f13e9f6e5786c95286ef98f49ab716119
Adds a ZPU register to control the FP GPIO source. These are 2bits
per GPIO pin, totalling 24 bits. 0 corresponds to RF-A, 1 corresponds
to RF-B. The following Python code will control the upper 6 bits of the
front-panel GPIO from the B-side radio on an X300:
>>> import uhd
>>> U = uhd.usrp.MultiUSRP("type=x300")
>>> U.get_gpio_src_banks()
['FP0']
>>> U.get_gpio_src("FP0")
['RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFA',
'RFA', 'RFA']
>>> U.set_gpio_src("FP0", ['RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFA',
'RFB', 'RFB', 'RFB', 'RFB', 'RFB', 'RFB'])
>>> U.get_gpio_src("FP0")
['RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFB', 'RFB', 'RFB', 'RFB',
'RFB', 'RFB']
>>> # Make all GPIOs outputs:
>>> U.set_gpio_attr("FP0A", "DDR", 0xFFF)
>>> U.set_gpio_attr("FP0B", "DDR", 0xFFF)
>>> # Control all GPIOs from software (not ATR):
>>> U.set_gpio_attr("FP0A", "CTRL", 0x000)
>>> U.set_gpio_attr("FP0B", "CTRL", 0x000)
>>> # Bottom 3 pins go high from radio A
>>> U.set_gpio_attr("FP0A", "OUT", 0x007)
>>> # Top 3 pins go high from radio B
>>> U.set_gpio_attr("FP0B", "OUT", 0xE00)
Amends the gpio.cpp example to allow switching the source.
Co-authored-by: Brent Stapleton <brent.stapleton@ettus.com>
Original-commit: d7304cc724de43b0d61d5b9d61a528d58898f004
The FPGA codebase was removed from the UHD repository in 2014 to reduce
the size of the repository. However, over the last half-decade, the
split between the repositories has proven more burdensome than it has
been helpful. By merging the FPGA code back, it will be possible to
create atomic commits that touch both FPGA and UHD codebases. Continuous
integration testing is also simplified by merging the repositories,
because it was previously difficult to automatically derive the correct
UHD branch when testing a feature branch on the FPGA repository.
This commit also updates the license files and paths therein.
We are therefore merging the repositories again. Future development for
FPGA code will happen in the same repository as the UHD host code and
MPM code.
== Original Codebase and Rebasing ==
The original FPGA repository will be hosted for the foreseeable future
at its original local location: https://github.com/EttusResearch/fpga/
It can be used for bisecting, reference, and a more detailed history.
The final commit from said repository to be merged here is
05003794e2da61cabf64dd278c45685a7abad7ec. This commit is tagged as
v4.0.0.0-pre-uhd-merge.
If you have changes in the FPGA repository that you want to rebase onto
the UHD repository, simply run the following commands:
- Create a directory to store patches (this should be an empty
directory):
mkdir ~/patches
- Now make sure that your FPGA codebase is based on the same state as
the code that was merged:
cd src/fpga # Or wherever your FPGA code is stored
git rebase v4.0.0.0-pre-uhd-merge
Note: The rebase command may look slightly different depending on what
exactly you're trying to rebase.
- Create a patch set for your changes versus v4.0.0.0-pre-uhd-merge:
git format-patch v4.0.0.0-pre-uhd-merge -o ~/patches
Note: Make sure that only patches are stored in your output directory.
It should otherwise be empty. Make sure that you picked the correct
range of commits, and only commits you wanted to rebase were exported
as patch files.
- Go to the UHD repository and apply the patches:
cd src/uhd # Or wherever your UHD repository is stored
git am --directory fpga ~/patches/*
rm -rf ~/patches # This is for cleanup
== Contributors ==
The following people have contributed mainly to these files (this list
is not complete):
Co-authored-by: Alex Williams <alex.williams@ni.com>
Co-authored-by: Andrej Rode <andrej.rode@ettus.com>
Co-authored-by: Ashish Chaudhari <ashish@ettus.com>
Co-authored-by: Ben Hilburn <ben.hilburn@ettus.com>
Co-authored-by: Ciro Nishiguchi <ciro.nishiguchi@ni.com>
Co-authored-by: Daniel Jepson <daniel.jepson@ni.com>
Co-authored-by: Derek Kozel <derek.kozel@ettus.com>
Co-authored-by: EJ Kreinar <ej@he360.com>
Co-authored-by: Humberto Jimenez <humberto.jimenez@ni.com>
Co-authored-by: Ian Buckley <ian.buckley@gmail.com>
Co-authored-by: Jörg Hofrichter <joerg.hofrichter@ni.com>
Co-authored-by: Jon Kiser <jon.kiser@ni.com>
Co-authored-by: Josh Blum <josh@joshknows.com>
Co-authored-by: Jonathon Pendlum <jonathan.pendlum@ettus.com>
Co-authored-by: Martin Braun <martin.braun@ettus.com>
Co-authored-by: Matt Ettus <matt@ettus.com>
Co-authored-by: Michael West <michael.west@ettus.com>
Co-authored-by: Moritz Fischer <moritz.fischer@ettus.com>
Co-authored-by: Nick Foster <nick@ettus.com>
Co-authored-by: Nicolas Cuervo <nicolas.cuervo@ettus.com>
Co-authored-by: Paul Butler <paul.butler@ni.com>
Co-authored-by: Paul David <paul.david@ettus.com>
Co-authored-by: Ryan Marlow <ryan.marlow@ettus.com>
Co-authored-by: Sugandha Gupta <sugandha.gupta@ettus.com>
Co-authored-by: Sylvain Munaut <tnt@246tNt.com>
Co-authored-by: Trung Tran <trung.tran@ettus.com>
Co-authored-by: Vidush Vishwanath <vidush.vishwanath@ettus.com>
Co-authored-by: Wade Fife <wade.fife@ettus.com>
Original-commit: bafa9d95453387814ef25e6b6256ba8db2df612f
- Fixed 10GigE firmware communication issues and sequence errors for TX
- Multiple changes to help ease timing closure
- Cleaned up build scripts
- Switched to Xilinx ISE 14.7 as the default build tool for X300
Original-commit: 64d71dcbc5fa6790385b288de25224d386b047b0
