Adds a BUILD_SEED make variable that can be set to a 32-bit integer,
and adds an FPGA read-only register initialized by this variable.
Changing this variable will randomly affect the FPGA build results.
This can be useful when your build fails timing by a small amount,
allowing you to build again and get different results with the same
code.
For example, you could run the following to produce an FPGA build with
different timing results from the default build:
make X310_XG BUILD_SEED=123
Original-commit: 3a3a03486f9221c2e59fa6d0826c23d17730956d
This updates all RFNoC devices so that they get the RFNoC protocol
version and CHDR width in the same way, from the output generated by
the RFNoC image builder.
Original-commit: 6f038dc2f69b38e715206b2e700fdd3a1bbc638e
This updates the IO signatures so that all devices and RFNoC blocks use
the same IO signature for the DRAM. This is needed because the IO
signatures must match between the RFNoC blocks and the devices. This
means that some devices have extra bits in the IO signature for the
address, but the extra bits will simply be ignored.
Original-commit: 8f09caaa06725d2364c63ac7cff02f3298895f4a
Make timekeeper tick on every cycle of the radio clock.
Signed-off-by: Michael West <michael.west@ettus.com>
Original-commit: 7886b71f13e9f6e5786c95286ef98f49ab716119
Adds a ZPU register to control the FP GPIO source. These are 2bits
per GPIO pin, totalling 24 bits. 0 corresponds to RF-A, 1 corresponds
to RF-B. The following Python code will control the upper 6 bits of the
front-panel GPIO from the B-side radio on an X300:
>>> import uhd
>>> U = uhd.usrp.MultiUSRP("type=x300")
>>> U.get_gpio_src_banks()
['FP0']
>>> U.get_gpio_src("FP0")
['RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFA',
'RFA', 'RFA']
>>> U.set_gpio_src("FP0", ['RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFA',
'RFB', 'RFB', 'RFB', 'RFB', 'RFB', 'RFB'])
>>> U.get_gpio_src("FP0")
['RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFB', 'RFB', 'RFB', 'RFB',
'RFB', 'RFB']
>>> # Make all GPIOs outputs:
>>> U.set_gpio_attr("FP0A", "DDR", 0xFFF)
>>> U.set_gpio_attr("FP0B", "DDR", 0xFFF)
>>> # Control all GPIOs from software (not ATR):
>>> U.set_gpio_attr("FP0A", "CTRL", 0x000)
>>> U.set_gpio_attr("FP0B", "CTRL", 0x000)
>>> # Bottom 3 pins go high from radio A
>>> U.set_gpio_attr("FP0A", "OUT", 0x007)
>>> # Top 3 pins go high from radio B
>>> U.set_gpio_attr("FP0B", "OUT", 0xE00)
Amends the gpio.cpp example to allow switching the source.
Co-authored-by: Brent Stapleton <brent.stapleton@ettus.com>
Original-commit: d7304cc724de43b0d61d5b9d61a528d58898f004
The FPGA codebase was removed from the UHD repository in 2014 to reduce
the size of the repository. However, over the last half-decade, the
split between the repositories has proven more burdensome than it has
been helpful. By merging the FPGA code back, it will be possible to
create atomic commits that touch both FPGA and UHD codebases. Continuous
integration testing is also simplified by merging the repositories,
because it was previously difficult to automatically derive the correct
UHD branch when testing a feature branch on the FPGA repository.
This commit also updates the license files and paths therein.
We are therefore merging the repositories again. Future development for
FPGA code will happen in the same repository as the UHD host code and
MPM code.
== Original Codebase and Rebasing ==
The original FPGA repository will be hosted for the foreseeable future
at its original local location: https://github.com/EttusResearch/fpga/
It can be used for bisecting, reference, and a more detailed history.
The final commit from said repository to be merged here is
05003794e2da61cabf64dd278c45685a7abad7ec. This commit is tagged as
v4.0.0.0-pre-uhd-merge.
If you have changes in the FPGA repository that you want to rebase onto
the UHD repository, simply run the following commands:
- Create a directory to store patches (this should be an empty
directory):
mkdir ~/patches
- Now make sure that your FPGA codebase is based on the same state as
the code that was merged:
cd src/fpga # Or wherever your FPGA code is stored
git rebase v4.0.0.0-pre-uhd-merge
Note: The rebase command may look slightly different depending on what
exactly you're trying to rebase.
- Create a patch set for your changes versus v4.0.0.0-pre-uhd-merge:
git format-patch v4.0.0.0-pre-uhd-merge -o ~/patches
Note: Make sure that only patches are stored in your output directory.
It should otherwise be empty. Make sure that you picked the correct
range of commits, and only commits you wanted to rebase were exported
as patch files.
- Go to the UHD repository and apply the patches:
cd src/uhd # Or wherever your UHD repository is stored
git am --directory fpga ~/patches/*
rm -rf ~/patches # This is for cleanup
== Contributors ==
The following people have contributed mainly to these files (this list
is not complete):
Co-authored-by: Alex Williams <alex.williams@ni.com>
Co-authored-by: Andrej Rode <andrej.rode@ettus.com>
Co-authored-by: Ashish Chaudhari <ashish@ettus.com>
Co-authored-by: Ben Hilburn <ben.hilburn@ettus.com>
Co-authored-by: Ciro Nishiguchi <ciro.nishiguchi@ni.com>
Co-authored-by: Daniel Jepson <daniel.jepson@ni.com>
Co-authored-by: Derek Kozel <derek.kozel@ettus.com>
Co-authored-by: EJ Kreinar <ej@he360.com>
Co-authored-by: Humberto Jimenez <humberto.jimenez@ni.com>
Co-authored-by: Ian Buckley <ian.buckley@gmail.com>
Co-authored-by: Jörg Hofrichter <joerg.hofrichter@ni.com>
Co-authored-by: Jon Kiser <jon.kiser@ni.com>
Co-authored-by: Josh Blum <josh@joshknows.com>
Co-authored-by: Jonathon Pendlum <jonathan.pendlum@ettus.com>
Co-authored-by: Martin Braun <martin.braun@ettus.com>
Co-authored-by: Matt Ettus <matt@ettus.com>
Co-authored-by: Michael West <michael.west@ettus.com>
Co-authored-by: Moritz Fischer <moritz.fischer@ettus.com>
Co-authored-by: Nick Foster <nick@ettus.com>
Co-authored-by: Nicolas Cuervo <nicolas.cuervo@ettus.com>
Co-authored-by: Paul Butler <paul.butler@ni.com>
Co-authored-by: Paul David <paul.david@ettus.com>
Co-authored-by: Ryan Marlow <ryan.marlow@ettus.com>
Co-authored-by: Sugandha Gupta <sugandha.gupta@ettus.com>
Co-authored-by: Sylvain Munaut <tnt@246tNt.com>
Co-authored-by: Trung Tran <trung.tran@ettus.com>
Co-authored-by: Vidush Vishwanath <vidush.vishwanath@ettus.com>
Co-authored-by: Wade Fife <wade.fife@ettus.com>
Original-commit: bafa9d95453387814ef25e6b6256ba8db2df612f
