# # Copyright 2022 Ettus Research, a National Instruments Brand # # SPDX-License-Identifier: LGPL-3.0-or-later # # Description: # Timing constraints exclusive to X410. These should be used # in conjunction with ./common.xdc # ############################################################################### # DB GPIO # This interface is defined as system synchronous to pll_ref_clk. # Some timing constants in this section are declared in # /fpga/usrp3/top/x400/constraints/timing/shared_constants.sdc ############################################################################### # Set output constraints for all ports. set db_gpio_ports [get_ports {DB0_GPIO[*] DB1_GPIO[*]}] set_output_delay -clock [get_clocks pll_ref_clk] -min $db_gpio_fpga_min_out $db_gpio_ports set_output_delay -clock [get_clocks pll_ref_clk] -max $db_gpio_fpga_max_out $db_gpio_ports # Output enable signal is available one clock cycle ahead of valid data, this # enables the use of multi-cycle paths. set db_gpio_out_en_regs [get_cells -hierarchical -filter \ {PRIMITIVE_TYPE =~ REGISTER.*.* && NAME =~ "*bytestream_output_enable*"}] set_multicycle_path 2 -setup -from $db_gpio_out_en_regs -to $db_gpio_ports set_multicycle_path 1 -hold -from $db_gpio_out_en_regs -to $db_gpio_ports # Calculate output delays back from capturing edge, add board delay and clock # difference. # Assume worst case as data being generated late and receiving an early clock: # - Max CPLD TCO # - Max data propagation delay # - Max CPLD clock propagation delay and minimum FPGA clock propagation delay # - Maximum delay from MC100EPT23 clock buffer set_input_delay -clock pll_ref_clk \ -max [expr {$pll_ref_clk_period - $db_gpio_cpld_max_out + $db_gpio_board_max_delay \ + $db_cpld_prc_clock_prop_max - $fpga_prc_clock_prop_min + $clock_translate_max}] \ $db_gpio_ports # Negate minimum output delay as it is defined from the change to the start # clock edge. # Assume worst case as data being generated early and receiving an late clock: # - Min CPLD TCO # - Min data propagation delay (0) # - Min CPLD clock propagation delay and max FPGA clock propagation delay set_input_delay -clock pll_ref_clk \ -min [expr {- $db_gpio_cpld_min_out \ - $db_gpio_board_min_delay \ - $db_cpld_prc_clock_prop_min + $fpga_prc_clock_prop_max}] \ $db_gpio_ports ############################################################################### # x410_ps_rfdc_bd ############################################################################### # This property tells Vivado that we require the clocks generated by the RFDC MMCM to be well # aligned. We have synchronous clock domain crossings between these clocks that can have # large hold violations after placement due to uneven clock loading. # The constraint CLOCK_DELAY_GROUP has to be applied on the clock nets. # These nets are connected to the outputs of the clock buffers, which are driven by the MMCM. # Search the nets begining from the MMCM outputs to find the clock buffers outputs. set rfdc_mmcm [get_cells -hierarchical -filter { PRIMITIVE_TYPE == CLOCK.PLL.MMCME4_ADV && NAME =~ *rfdc/data_clock_mmcm* } ] set mmcm_clkout_pins [get_pins -of_objects $rfdc_mmcm -regexp -filter {NAME =~ ".*CLKOUT[0-4]"}] set mmcm_clkout_nets [get_nets -of_objects $mmcm_clkout_pins] set clkbuf_in_pins [get_pins -leaf -of_objects $mmcm_clkout_nets -filter {DIRECTION == IN}] set clkbuf_cells [get_cells -of_objects $clkbuf_in_pins] set clkbuf_out_pins [get_pins -of_objects $clkbuf_cells -filter {DIRECTION == OUT}] set clkbuf_out_nets [get_nets -of_objects $clkbuf_out_pins] set_property CLOCK_DELAY_GROUP DataClkGroup $clkbuf_out_nets # We treat rfdc_clk buffers as asynchronous, with knowledge that # code clocked in this domain will be reset after this clocked is enabled. This # will make timing easier to meet on these clock domains. # set_false_path -from [get_cells -hierarchical -regexp -filter {NAME =~ .*/rfdc/clock_gates_0/.*rEnableRfdc\dBufg.*_reg}] set_false_path -from [get_cells -hierarchical -regexp -filter {NAME =~ .*/rfdc/clock_gates_0/.*rEnableDataBufg\dx.*_reg}] set_false_path -from [get_cells -hierarchical -regexp -filter {NAME =~ .*/rfdc/clock_gates_0/.*rEnableRfdcBufg\dx.*_reg}] ############################################################################### # SPLL SYSREF Capture ############################################################################### # SYSREF is generated by the LMK04832 clocking chip (SPLL), which also produces # the PLL reference clock (PRC) used to generate data clocks with a MMCM. Both # SYSREF and PLL reference clock are directly fed into the RFSoC. # The LMK04832 is configured to output all clocks synchronized to the # rising edge of SYSREF. SYSREF is first captured by the FPGA fabric in the # PRC clock domain (MMCM's PRC output) on the falling edge to meet setup and # hold times. Afterwards it is captured with a double synchronizer and then # transferred to the RFDC clock domain. Both SYSREF versions (PRC and RFDC) # are used by downstream logic for sync purposes. # The highest PRC frequency supported in MPM (64 MHz) is used for # timing constraints. # Set SYSREF LMK Delay to 0 ns as we assume rising edge alignment from the # LMK04832 chip. set sysref_lmk_delay 0 # # These are the signals' lengths and corresponding delays (assuming 170 ps/in): # - SYSREF --> 5794 mils (5.794 inches) = 0.985 ns # - PRC --> 5668 mils (5.668 inches) = 0.964 ns # # For min/max input delay calculations, it is assumed min prop. delay of 0 ns, # which essentially over-constrains SYSREF. # # The max input delay is the latest that SYSREF may arrive w.r.t PRC, and it is # calculated as follows: # Input delay (max) = SYSREF's LMK delay + SYSREF prop. delay (max) # - PRC prop. delay (min) set sysref_max_input_delay [expr {$sysref_lmk_delay + 0.985 - 0}] # # The min input delay is the earliest that SYSREF may arrive w.r.t PRC, and it # is calculated as follows: # Input delay (min) = SYSREF's LMK delay + SYSREF prop. delay (min) # - PRC prop. delay (min) set sysref_min_input_delay [expr {$sysref_lmk_delay + 0 - 0.964}] set_input_delay -clock pll_ref_clk -max $sysref_max_input_delay [get_ports {SYSREF_FABRIC_P}] set_input_delay -clock pll_ref_clk -min $sysref_min_input_delay [get_ports {SYSREF_FABRIC_P}] ############################################################################### # SPI to MB CPLD (PL) # This interface is defined as system synchronous to pll_ref_clk. ############################################################################### # The output delays are chosen to allow a large time window of valid data for # the MB CPLD logic. set spi_min_out_delay 0.000 set spi_max_out_delay 11.000 # Set output constraints for all ports. set spi_out_ports [get_ports {PL_CPLD_SCLK PL_CPLD_MOSI PL_CPLD_CS0_n PL_CPLD_CS1_n}] set_output_delay -clock [get_clocks pll_ref_clk] -min $spi_min_out_delay $spi_out_ports set_output_delay -clock [get_clocks pll_ref_clk] -max $spi_max_out_delay $spi_out_ports # Force SPI registers into IOB. set_property IOB TRUE [get_cells "cpld_interface_i/ctrlport_spi_master_i/simple_spi_core_64bit_i/sclk_reg"] set_property IOB TRUE [get_cells "cpld_interface_i/ctrlport_spi_master_i/simple_spi_core_64bit_i/mosi_reg"]